South Dakota DPS CDL General Knowledge Practice Test 1

Test 1 of 5. Pick an answer for each question to see if it is right and why; your score appears at the end. You need 40 correct answers to pass, the same ratio as the real South Dakota test.

A highway through grasslands and rocky hills, a typical landscape of South Dakota
  1. 1. On a multilane highway, which lane should a heavy vehicle normally use?

    Show answer

    Answer A: The right lane, except to pass or where signs direct otherwise

    Keeping right leaves the faster lanes free and reduces the number of vehicles that have to move around a slower, heavier vehicle.

  2. 2. When a railroad crossing signal gives a warning, within what distance must a South Dakota driver stop, according to state law?

    Show answer

    Answer A: Within 50 feet but not less than 15 feet from the nearest rail

    State law requires stopping within 50 feet but not closer than 15 feet from the nearest rail when a crossing signal gives warning.

  3. 3. How should speed and gears be handled when approaching a curve?

    Show answer

    Answer A: Slow to a safe speed and downshift before entering the curve

    Braking and shifting are completed before the curve so the vehicle is settled and can pull gently through it without upsetting the load.

  4. 4. With water standing on the road, hydroplaning can begin at speeds as low as what?

    Show answer

    Answer D: 30 mph

    When enough water covers the surface, the tires can ride up on it and lose contact at speeds as low as 30 mph.

  5. 5. Which components on a typical engine are driven by belts that must be checked for wear and tension?

    Show answer

    Answer D: The alternator, the water pump and, on many vehicles, the air compressor

    Belts drive accessories such as the alternator, the water pump and the air compressor, so one failed belt can take out charging, cooling or air supply.

  6. 6. You have backed into the same loading bay every week for a year. How often should you still get out and walk to the rear before backing?

    Show answer

    Answer D: Every time, since the area can change while you are away from it

    A familiar space is no guarantee; vehicles, pallets, people and overhead obstructions appear between one visit and the next, so you check on every occasion.

  7. 7. What is the driver responsible for when a load is covered with a tarp?

    Show answer

    Answer C: Fastening it so it cannot flap free, block a mirror, or come off in the wind

    A tarp that works loose can tear away, block the driver view or the view of others, and become a hazard for the traffic behind.

  8. 8. What tells a driver when to shift up in a vehicle with a manual transmission?

    Show answer

    Answer C: Engine speed in rpm together with road speed

    Shift points are judged from engine rpm and road speed, using the operating range the manufacturer specifies for that engine.

  9. 9. A 40 foot straight truck and a 70 foot tractor-trailer make the same right turn. Which needs more room and why?

    Show answer

    Answer B: The tractor-trailer, because the longer the vehicle the farther inside the rear wheels track

    Off-tracking grows with the distance between the front and rear axles, so the longer combination cuts the corner much more sharply and needs extra room.

  10. 10. Which vehicle condition makes hydroplaning more likely?

    Show answer

    Answer C: Tires that are worn or underinflated

    Tread depth and correct pressure are what let a tire push water aside, so worn or soft tires lift onto the water film at lower speeds.

  11. 11. At 55 mph, about how far does a vehicle travel during a typical 3/4 second perception time plus 3/4 second reaction time, before the brakes even begin to work?

    Show answer

    Answer C: About 120 feet

    Each 3/4 second at 55 mph covers about 60 feet, so perception and reaction together use up roughly 120 feet before braking starts.

  12. 12. For how long is a South Dakota commercial learner's permit valid before it must be reissued with new testing?

    Show answer

    Answer A: No more than one year

    A commercial learner's permit cannot be valid for more than one year, and renewal requires retaking the knowledge and skills tests.

  13. 13. A fire has started in the vehicle. How should the extinguisher be used?

    Show answer

    Answer B: Stay as far back as the reach of the extinguisher allows, stand upwind, and aim at the base of the fire

    Aiming at the base attacks what is actually burning, and staying upwind and well back protects the driver from heat, smoke and the flames themselves.

  14. 14. During the walkaround you notice one tire on an axle is a radial and the tire next to it is bias-ply. What should you do?

    Show answer

    Answer B: Treat it as a defect, because radial and bias-ply tires must not be mixed on the same axle

    Radial and bias-ply tires flex and grip differently, so mixing them on one axle makes the vehicle handle unpredictably and is not allowed.

  15. 15. What must be true of the person who performs the annual periodic inspection?

    Show answer

    Answer D: They must meet the federal qualification requirements for an inspector

    The inspection has to be done by someone who meets the federal training and experience requirements for inspectors, whoever employs them.

  16. 16. You drop your phone on the floor of the cab while driving. What do federal rules require?

    Show answer

    Answer A: Leave it, because reaching for it while driving is banned

    Federal rules forbid reaching for a mobile device in any way that takes the driver out of a seated, belted driving position.

  17. 17. Regular mirror checks during a long trip can reveal which developing problem?

    Show answer

    Answer D: Smoke coming from a tire or from a wheel

    Overheating tires, wheel bearings and brakes usually show as smoke long before anything appears on the dash, and mirrors are where a driver sees it.

  18. 18. You stop to check the load. Which set of things are you looking at?

    Show answer

    Answer C: Tight tiedowns, cargo that has not moved, secure doors and tarps still fastened

    A cargo check covers the load and everything holding it: whether it has shifted, whether the devices are still tight, and whether doors and covers are still closed and fastened.

  19. 19. Which of these is NOT on the federal list of parts and accessories the driver must be satisfied are in good working order before driving?

    Show answer

    Answer D: The seat cushion upholstery

    The federal pre-trip rule names brakes, steering, lights and reflectors, tires, horn, wipers, mirrors, coupling devices, wheels and rims, and emergency equipment; seat upholstery is not on that list.

  20. 20. How long must a motor carrier keep a driver vehicle inspection report and the certification of repairs?

    Show answer

    Answer B: Three months

    The original report and the certifications attached to it are kept on file for three months from the date the report was prepared.

  21. 21. You are told a posted bridge ahead has a weight limit lower than your gross weight. What must you do?

    Show answer

    Answer C: Take a route that avoids it, because a posted limit is a legal limit

    A posted structure limit must be obeyed exactly as any other weight limit, so a heavier vehicle has to be routed around it.

  22. 22. While checking the in-cab gauges after start-up, what should the coolant temperature gauge do?

    Show answer

    Answer C: Rise gradually to the normal operating range

    A healthy cooling system warms the engine slowly; a gauge that shoots up or stays cold points to a problem with the thermostat, coolant or sensor.

  23. 23. What are you checking on the mud flaps during the walkaround?

    Show answer

    Answer C: That they are securely attached, not torn and not dragging on the ground

    A flap that is torn or hanging loose stops shielding following traffic from spray and stones, and a dragging flap can catch and tear away on the road.

  24. 24. What is axle weight?

    Show answer

    Answer C: The weight carried to the ground by one axle or one set of axles

    Axle weight describes how the load is shared among the axles that carry it to the road, not how much the whole vehicle weighs.

  25. 25. What must be checked on a sliding fifth wheel during the inspection?

    Show answer

    Answer B: That it is locked in position and not so far forward that the trailer can hit the cab

    A slider that is unlocked can move under braking, and one set too far forward lets the trailer strike the cab when the tractor turns sharply.

  26. 26. Total stopping distance is made up of which parts?

    Show answer

    Answer A: Perception distance, reaction distance and braking distance

    The vehicle travels while the hazard is recognized, while the driver moves to the pedal, and again while the brakes slow the vehicle.

  27. 27. How soon must warning devices be placed after a commercial vehicle stops on the traveled part or the shoulder of a highway?

    Show answer

    Answer D: As soon as possible and in any case within 10 minutes

    The hazard warning flashers go on immediately and the warning devices must be in place as soon as possible, never later than 10 minutes after stopping.

  28. 28. An article of cargo has been blocked so that it cannot move forward. How many tiedowns does the federal rule call for?

    Show answer

    Answer A: One tiedown for every 10 feet of article length, or any part of that

    Blocking against forward movement lowers the requirement to one tiedown per 10 feet of length or fraction of 10 feet.

  29. 29. Which set of maneuvers makes up the basic control skills part of the commercial driving test?

    Show answer

    Answer D: Straight line backing, offset backing, parallel parking and alley docking

    The basic control skills test is carried out off the road and consists of low speed exercises such as straight line backing, offset backing, parallel parking and the alley dock.

  30. 30. You are about to cross a long, high bridge with a light load in gusty wind. What should you do?

    Show answer

    Answer C: Slow down and be ready for a sudden push

    Wind is strongest where a bridge leaves the shelter of the land, and lower speed gives you time to correct when the first gust hits.

  31. 31. On a wet road, a commercial driver should reduce speed by roughly how much?

    Show answer

    Answer C: By about one third

    Cutting speed by roughly a third, for example from 55 to about 35 mph, restores a margin for the traction lost on a wet surface.

  32. 32. Which windshield condition should be reported during the inspection?

    Show answer

    Answer B: Cracks or dirt that get in the way of your view of the road

    The windshield must give a clear view; damage or grime in the driver line of sight is a safety defect.

  33. 33. Why does extra weight make a long downgrade more dangerous even when the brakes are in good order?

    Show answer

    Answer B: Gravity adds to the momentum and the brakes heat up faster

    The heavier the vehicle, the more energy the brakes must turn into heat, and heat is exactly what makes brakes fade on a long descent.

  34. 34. Why are the windshield wipers on the pre-trip list even before a trip in fine weather?

    Show answer

    Answer C: Because weather can change and a wiper failure leaves the driver without a clear view

    Rain, spray or mud can arrive at any point in a long trip, and a wiper that fails then leaves the driver with no way to clear the windshield.

  35. 35. If a South Dakota commercial learner's permit holder needs to renew the permit after it lapses, what must they do?

    Show answer

    Answer B: Retake the required knowledge and skills test segments

    Renewing a commercial learner's permit requires retaking all the required knowledge and skills test segments; a prior skills test score becomes invalid.

  36. 36. How are the extra gears of a multi-speed rear axle or auxiliary transmission usually controlled?

    Show answer

    Answer D: With a selector knob or switch on the gearshift lever of the main transmission

    A range selector on the shift lever lets the driver choose the extra gear range while shifting the main transmission.

  37. 37. Why is braking while in a curve dangerous in a heavy vehicle?

    Show answer

    Answer A: The wheels lock more easily and the vehicle can skid

    Tires already using their grip to turn have little left for braking, so hard braking in a curve locks the wheels; slow down before the curve instead.

  38. 38. Which wheel or rim condition must be treated as a defect during the walkaround?

    Show answer

    Answer C: Cracks, illegal welded repairs, or missing and loose lug nuts

    Cracked or welded rims and missing or loose fasteners can let a wheel separate from the vehicle and must be corrected before driving.

  39. 39. Where on the road are you most likely to find ice in cold weather?

    Show answer

    Answer B: On bridges, overpasses and shaded stretches, which freeze before the rest of the road

    Bridges and overpasses lose heat from above and below, and shaded areas get no sun, so they ice over first and stay icy longest.

  40. 40. Who has the authority to set the maximum speed for heavy vehicles, such as those over 10,000 pounds gross weight, on South Dakota highways?

    Show answer

    Answer C: The Transportation Commission, through adopted rules

    State law directs the Transportation Commission to adopt rules setting the maximum speed for heavy vehicles rather than fixing a single number in the statute itself.

  41. 41. Rust streaks are running outward from the lug nuts on one wheel. What does this most likely indicate?

    Show answer

    Answer C: The lug nuts may be loose

    Rust trails spreading from the nuts are a classic sign that the nuts have worked loose and the wheel has been moving on the studs.

  42. 42. With the tractor coupled to the trailer, what should you see between the upper and lower fifth wheel plates?

    Show answer

    Answer A: No space at all between the two plates

    Any daylight between the plates means the trailer is not properly seated on the fifth wheel and the coupling can come apart under load.

  43. 43. When should mirror adjustment be checked, and what should each mirror show?

    Show answer

    Answer B: Before every trip, with each mirror adjusted to show some part of the vehicle

    Checking the mirrors before each trip and keeping a small part of the vehicle in view gives a reference point for judging distance behind and beside you.

  44. 44. Does the federal texting ban apply to a company dispatching device mounted in the cab?

    Show answer

    Answer B: Yes, entering or reading text on it while driving is banned

    The rule is written around the act of reading or entering text on any electronic device, not around who owns the device.

  45. 45. What does South Dakota require a commercial driver to carry while operating a commercial motor vehicle?

    Show answer

    Answer D: The commercial learner's permit or commercial driver license with the applicable endorsements, in immediate possession

    No person may drive a commercial motor vehicle in South Dakota without holding and having in immediate possession a commercial learner's permit or CDL valid for that vehicle.

  46. 46. Part of your load stands high enough to hide a rear lamp or a reflector. What must be done?

    Show answer

    Answer B: The load must be moved or extra lamps fitted so the required lights can be seen

    Required lamps and reflectors must remain visible; if the cargo blocks them, the load is rearranged or additional lamps are fitted so the vehicle can still be seen.

  47. 47. Why should a long vehicle never swing out to the left before starting a right turn?

    Show answer

    Answer D: Another driver may read it as a left turn or pass on your right

    Swinging left opens a gap on your right that a car will move into, and it also sends a false message about which way you are going.

  48. 48. Before raising the hood to inspect the engine compartment, what should you do?

    Show answer

    Answer B: Shut off the engine, set the parking brake and chock the wheels if needed

    The engine compartment is inspected with the engine off and the vehicle secured so nothing can move or turn while your hands are inside.

  49. 49. Where should a driver expect fog to form first?

    Show answer

    Answer D: In low ground, near water and in valleys

    Cool moist air settles in low places, so fog patches appear in hollows, river valleys and near lakes before they appear anywhere else.

  50. 50. When is a road surface usually most slippery during a rain shower?

    Show answer

    Answer A: Just after the rain starts, when water mixes with oil and dirt on the surface

    The first rain lifts oil and dust into a slick film that has not yet been washed away, so the road is more slippery than it will be later.